Error Occurred While Attempting To Read The Boot Configuration Data
Boot/BCD 0xc000000f Error Windows 7 April 17, 2015 8:01 am / 125 Comments / D.A.R.Y.L. This article is specific to Windows 7 but similar errors occur on all versions of windows. NOTE: You will need your Windows 7 DVD or
Error Occurred While Attempting To Read The Boot Configuration Data Windows 7
a USB with the recovery console installed. IF USING A USB STICK MAKE SURE IT boot manager not found IS PLUGGED INTO A USB 2 SLOT, USB 3 IS NOT SUPPORTED; It will error with ‘failure when attempting to copy boot file'. After rebooting boot bootmgr your computer you receive the following error: Windows Boot Manager Windows failed to start. A recent hardware or software change might be the cause. To fix the problem: 1.insert windos cd and run a repair your computer option. File:
An Error Occurred While Attempting To Read The Boot Configuration Data Wds
/boot/bcd Status: 0xc000000f Info: an error occurred while attempting to read the boot configuration data. You may receive a similar error which lists the error code as 0xc0000034 or missing file: windows\system32\winload.exe instead. You may also receive further errors after trying to repair the bcd store using bootrec and bcdedit as follows. The requested system device cannot be found. The "Windows Boot Configuration Data File is Missing Required Information The "Windows Boot Configuration Data File is Missing
An Error Occurred While Attempting To Read The Boot Configuration Data Pxe
An error occurred while attempting to read the boot configuration data Cause and Fix The most likely cause of this error is that you tried to dual boot two operating systems and then later decided to remove one. This inadvertently may have deleted the bcd boot store. The trick here is to run the above commands in the right order and set your boot partition to active. Let's get started. Make sure your boot partition is set to Active Boot from your DVD and choose the repair option. From the recovery console type "diskpart" and press enter and then type "list disk" to get a list of physical disks installed. In the example here I only have one disk in my machine, if you have more than one identify the disk which has the Windows boot partition on it and then select it. Select it by typing "select disk 0" (in my case). Now type "list partition". The Windows 7 boot partition is a 200 MB primary partition. As you can see here it was on disk 0. Select it by typing "select partition 2" or whichever number matches your 200MB partition. Now type "detail partition" and look where it says "Active". If it says yes then move onto the next section otherwise type "Active" and press enter, Windows should report the partition is now marked as active. No
Attempting to Read the Boot Configuration Data) is caused by missing or corrupt BCD registry hive.Find out how to fix error 0xC000000F (status 0xC000000F) an error occurred while attempting to read the boot configuration data usb by rebuilding BCD from scratch, using Emergency Boot CD. Contents 1. Symptoms
An Error Occurred While Attempting To Read The Boot Configuration Data Sccm
of the problem 2. Normal boot sequence 3. Defect in the boot sequence which leads to 'status an error occurred while attempting to run privileged commands 0xC000000F' boot error 4. How to fix status 0xC000000F 1. Symptoms of the problem When computer is powered up, an error message "Status: 0xc000000fInfo: An error occured while http://www.think-like-a-computer.com/2015/04/17/boot-bcd-0xc000000f-windows-7/ attempting to read the boot configuration data" appears: 2. Normal boot sequence The rest of this article refers to Windows 7, but all information below applies to Windows Vista and Windows 8 as well. Normally Windows 7 boots as shown below: BIOS loads 1st sector from HDD (Master Boot Record), verifies 55 AA signature and transfers control to http://www.prime-expert.com/articles/b17/fix-0xC000000F-error-reading-boot-configuration-data.php Master Boot Record. Master Boot Record scans partition table for active partition, then it loads 1st sector from active partition, verifies 55 AA signature, and transfers control to Boot Sector. Boot Sector loads 15 additional sectors from the beginning of disk (Volume Boot Record) and transfers control to first additional sector of VBR. Volume Boot Record loads BOOTMGR file from root directory of boot partition into the memory and transfers control to it. BOOTMGR loads Boot\BCD registry hive and displays boot menu. BOOTMGR is able to run memory test and set safe mode boot flag per explicit user request. But normally, it loads winload.exe when computer boots normally (cold startup) or winresume.exe (when computer resumes from hibernation). Winload.exe opens SYSTEM registry hive, gets list of drivers, loads NTOSKRNL.exe, loads drivers (*.SYS files) and transfers control to NTOSKRNL.exe. Winresume.exe loads memory dump from hiberfil.sys and transfers control to it. 3. Defect in the boot sequence which leads to 'status 0xC000000F' boot error Defect in the boot sequence which is a rea
be down. Please try the request again. Your cache administrator is webmaster. Generated Wed, 12 Oct 2016 20:16:27 GMT by s_ac5 (squid/3.5.20)
here for a quick overview of the site Help Center Detailed answers to any questions you might have Meta Discuss the workings and policies of this site About Us Learn more about Stack Overflow the company Business Learn more about hiring developers or posting ads with us Super User Questions Tags Users Badges Unanswered Ask Question _ Super User is a question and answer site for computer enthusiasts and power users. Join them; it only takes a minute: Sign up Here's how it works: Anybody can ask a question Anybody can answer The best answers are voted up and rise to the top An error occurred while attempting to read the boot configuration data up vote 0 down vote favorite My laptop is not getting started, it's unable to boot Windows 7. It shows the following error: File: \Boot\BCD Status: 0xc000014c info: an error occurred while attempting to read the boot configuration data. How can I boot my Windows? windows-7 boot bootloader bcd share|improve this question edited Jul 31 '13 at 12:19 karel 6,83992227 asked Jul 31 '13 at 10:43 ANTRIX 3113 also i dont have external recovery disk , just internal recovery on system hard disk –ANTRIX Jul 31 '13 at 11:00 add a comment| 1 Answer 1 active oldest votes up vote 1 down vote accepted Windows Boot Menu First of all try to tap F8 when the computer is booting, untill you see the Windows boot menu and then select Use last known good configuration. If Windows has worked before, then you might have a chance that this works. BCD Repair I don't think that you are that lucky, because it's the BCD which looks like being damaged. and since it is a very essential part of Windows, then it will require some sort of bootable Windows installation disk to repair. Check out my answer here on how to make a bootable Windows 7 installation USB. Repair Windows BCD - This will guide you through how to repair and hopefully getting your Windows 7 back to starting normally again. Factory reset A last thing you could try is a Factory reset. This is will put your computer back to the state where you started the computer for the first time. You can find a guide on how to do this on the manufacturer's website. share|improve this answer answered Jul 31 '13 at 11:23 Jesper Jensen 624411 tried many things. at last factory reset is the best option –ANTRIX Aug 2 '13 at 3:48 I'm glad you found a solution at least :) –Jesper Jensen Aug 2 '13 at 5:48 add a comment| Your Answer draft saved draft discarded Sign up or log in Sign up using Google Sign up using Facebook Sign up using Email