0502 Error Hardware
Contents |
für die Unannehmlichkeiten. Es gab einen
Hardware Error 9216
Fehler bei der Anwendung. es Lamentamos las molestias. Se ha producido un error en la aplicación. it Ci scusiamo per l'inconveniente. C'è stato un errore con l'applicazione. br Lamentamos o inconveniente. Houve um erro com o aplicativo.
the above message. This occurs when attempting all operations, Maintenance, cleansing, copying etc... Any ideas.???? John Respond to this 0 HI try this its from the lexmark web siteHardware Error 0502 on LCD Display ID:ENUS16536Check the encoder strip http://www.fixyourownprinter.com/forums/printer/34491 on the printer. (This is a clear strip running the length of the printer, above or behind the cartridge carrier.) Do the following:1. Switch off the printer using the power button. 2. Disconnect the power cable from the back http://www.justanswer.com/printers/2vusz-hardware-error-0502-what-do.html of the Lexmark X5100 / X6100 Series. 3. Leave the power cable disconnected for 30 seconds. 4. Slide the cartridge carrier to the middle of the printer by taking the top part of the belt and moving it gently hardware error to the right. 5. Take out both cartridges. 6. Place an index finger on the encoder strip on either side of the cartridge carrier. 7. On the back of the cartridge carrier, there is a small slot that the encoder strip fits into. Slightly push the encoder strip down and then back up to get it into the slot. 8. Lightly press the strip first to the rear and then forward, if necessary. 9. Clean the encoder strip with hardware error 0502 a dry tissue. Also clean the contacts of the printer. 10. Reconnect the power cable and switch the printer on again. 11. Perform the hardware test without cartridges first and then with both cartridges.* 12. Make a standalone copy. 13. If the copy is satisfactory, repeat the test once to confirm that the error is gone.How to Perform the Hardware Test on the Lexmark X5150 ID:ENUS3744Using the operator panel on the printer: 1. Press the Option button 10 times until Cartridges appears on the LED display. 2. Press the + button 4 times until Self test appears on the LED Display. 3. Press Select. The printer should print a sheet of paper with one black bar and one grey bar. 4. If the printer fails to print, remove both cartridges and try the test again. (It will feed the paper through and print a blank page.) 5. If the test works with no cartridges in the printer, run it again with one cartridge at a time installed. by [emailprotected] on Dec 20, 2005 at 2:08am Add comment Please sign in to comment Thank you so much for these instructions. They worked great to fix my Lexmark X5150 printer. Love that I keep finding instructions online to keep this beast going and going. - Nitecat Hi MattThanks for your instructions - a bit beyond a Grandma but fortunately my son was visiting -
by a Fortune 500 verification firm. Get a Professional Answer Via email, text message, or notification as you wait on our site.Ask follow up questions if you need to. 100% Satisfaction Guarantee Rate the answer you receive. Ask Freddy M. Your Own Question Freddy M., Technician Category: Printers Satisfied Customers: 18398 Experience: Years of IT and customer support experience 15852642 Type Your Printers Question Here... Freddy M. is online now Hardware error 0502 What do I do Resolved Question: Hardware error 0502What do I do? Submitted: 6 years ago. Category:Printers Share this conversation Expert: Freddy M. replied6 years ago. Hardware Error 0502 on LCD Display Check the encoder strip on the printer. (This is a clear strip running the length of the printer, above or behind the cartridge carrier.) Do the following: 1. Switch off the printer using the power button. 2. Disconnect the power cable from the back of the Lexmark X5100 / X6100 Series. 3. Leave the power cable disconnected for 30 seconds. 4. Slide the cartridge carrier to the middle of the printer by taking the top part of the belt and moving it gently to the right. 5. Take out both cartridges. 6. Place an index finger on the encoder strip on either side of the cartridge carrier. 7. On the back of the cartridge carrier, there is a small slot that the encoder strip fits into. Slightly push the encoder strip down and then back up to get it into the slot. 8. Lightly press the strip first to the rear and then forward, if necessary. 9. Clean the encoder strip with a dry tissue. Also clean the contacts of the printer. 10. Reconnect the power cable and switch the printer on again. 11. Perform the hardware test without cartridges first and then with both cartridges.* 12. Make a standalone copy. 13. If the copy is satisfactory, repeat the test once to confirm that the error is gone. How to Perform the Hardware Test on the Lexmark Using the operator panel on the printer: 1. Press the Option button 10 times until Cartridges appears on the LED display. 2. Press the + button 4 times until Self test appears on the LED Display. 3. Press Select. The printer should print a sheet of paper with one black bar and one grey bar. 4. If the printer fails to print, remove both cartridges and try the test again. (It will feed the paper through and print a blank page.) 5. If the test works with no cartridges in the printer, run it again with one cartridge at a time installed. --------------------------------------------------