Canon Printer Hardware Error
Contents |
could happens on these printers models: IPF6350, IPF6300, IPF6000, IPF8000, IPF8300, etc... Solution 1: Power off the printer. Disconnect the power cable Wait for 30 minutes. Connect the power cable Power on canon ipf750 hardware error Solution 2: Check the power supply Solution 3: The voltage of the print
Canon Ipf710 Hardware Error
head is abnormal. Replace the Printhead Solution 4: Check for the cable continuity between the carriage relay PCB and the main
Canon Hardware Error 03130031-2f26
controller PCB Replace the cable. Replace the carriage relay PCB. Replace the main controller PCB Libellés : Canon IPF 1 comment: aparsons said... The Canon troubleshooting guide says, It is not the power
Canon Hardware Error 03130031-2f50
supply. I changed the power supply. It was not the power supply. According to an experienced technician on the forums it is always the controller board.I did not change the printheads as the error occurred whether the printheads were installed or not. Also the error occurred without variation when I forgot to put the timing strip back in.I believe the Vh voltage error is a red herring and canon printer software it is just the error message that is displayed when the main controller board fails in this manner.The technician's troubleshooting guide says if there is no continuity error on the flat cables (very unlikely unless they have been damaged) to replace the main controller, the printheads and the carriage in that order. June 24, 2014 at 12:55 PM Post a Comment Newer Post Older Post Home Subscribe to: Post Comments (Atom) SSC Service Utility Software to reset Epson printers Canon Inkjet Printheads Error codes and solutions Fix and repair your laptop Fix your printer... in french ! French Site L'imprimante en question Friends Archaeology news Libellés Brother (6) Brother DCP (5) Brother HL (1) Brother MFC (6) Cano IR (1) Cano S (1) canon (29) Canon BJC (2) Canon i (6) Canon IP (1) Canon IPF (1) Canon IR (6) Canon LBP (1) Canon MPC (1) Canon MX (4) Canon Pixma (27) Canon S (2) Canon SmartBase (1) Dell laserjet (1) Epson (12) Epson Aculaser (2) Epson C (2) Epson DFX (1) Epson FX (1) Epson RX (2) Epson Stylus Photo (5) Epson Stylus Pro (3) Epson WorkForce (1) er (2) Error code (159) HP (27) HP Color laserjet (2) HP Design
> Raw & Post Processing, Printing > Printing: Printers, Papers and Inks > Canon iPF 6300 Hardware Error Pages: [1] 2 Go Down Print Author Topic: Canon iPF 6300 Hardware Error (Read 11171 times) Mike Raub Jr. Member Offline Posts: 70 hp printer hardware Canon iPF 6300 Hardware Error « on: December 23, 2013, 10:17:18 AM » I'm epson printer hardware being plagued with Hardware Error 03130031-2618 on my Canon iPF 6300. The message pops up as soon as the printer starts a canon ipf750 hardware error 03130031-2618 print job. Sometimes restarting the printer clears the message and then the printer works fine, but not this morning. Anyone have any idea what this error message means? The manual was no help at all.Thanks. http://fix-your-printer.blogspot.com/2014/06/how-to-solve-error-code-03130031-2618.html Logged rvonmayr Newbie Offline Posts: 26 Re: Canon iPF 6300 Hardware Error « Reply #1 on: December 23, 2013, 12:28:17 PM » In the Canon 6400 service manual, this is a 24 Volt power supply error (Voltage reads high)"VH voltage error", "Check the power supply unit."The power supply is located on the left rear side of the printer.The 6300 power supply part number is ""QK1-5927-000", retailing for about $125.The power supply is http://forum.luminous-landscape.com/index.php?topic=85404.0 NOT common between 6400 and 6300 (different part number), but for the 6400 here is the connections on the main controller wiring:CN2 (Connect to Main Controller)Pin Number Signal name IN/OUT Function1 HD_VHFBH IN VH feedback voltage +2 HD_VHFBG IN VH feedback voltage -3 VH OUT Power supply (+24V)4 VH_GND - GND5 VH OUT Power supply (+24V)6 VH_GND - GND7 VM OUT Power supply (+32V)8 VM_GND - GND9 VM OUT Power supply (+32V)10 VM_GND - GND11 VH_ENB IN VH power supply ON/OFF signal12 PW_CONT IN Normal/power saving switch signalBest Regards,Robert « Last Edit: December 23, 2013, 12:39:44 PM by rvonmayr » Logged Best Regards,Robert Mike Raub Jr. Member Offline Posts: 70 Re: Canon iPF 6300 Hardware Error « Reply #2 on: December 24, 2013, 10:50:01 AM » Robert, thank you very much for the detailed information. Since the problem is intermittent and the printer seems to work fine once I get past the error message, I wonder if it is possible to do something like a master reset of the printer, in case this is just a spurious error message. I'm visiting family for the holidays and don't have access to the manual from my iPad, though I did not see a reset option while scrolling through the printer menus. Thanks again. Logged rvonmayr New
Recommendations hardware error Known Limitations Latest Drivers FAQ Contents Pre-PurchaseSetupToolsPrinter Control PanelPaperPhotoshop PluginUsageMaintenanceTroubleshootingFAQ (Single Page) Favorite Papers Matboard/Paper Colors Canon Profiles Generic Profiles Custom Profiles Profiling canon ipf750 hardware i1 Match RIP Support Gamut Plots iPF5000 Download Gamut Movie Wiki Member Location Return to Discussion Help · About · Blog · Pricing · Privacy · Terms · Support · Upgrade Contributions to http://canonipf.wikispaces.com/ are licensed under a Creative Commons Attribution Share-Alike 2.5 License. Portions not contributed by visitors are Copyright 2016 Tangient LLCTES: The largest network of teachers in the world Turn off "Getting Started" Home ... Loading...